RN 4Z

SANKEN ELECTRIC CO., LTD. RN4Z 1. Scope The present specifications shall apply to an RN4Z. 2. Outline Silicon Diode Structure Resin Molded Applications High Frequency Rectification ns Type N ot R ec o m m en de d fo rN ew D es ig 3. Flammability UL94V-0(Equivalent) ‘110518 SSA-03953 1／7 61426-01 SANKEN ELECTRIC CO., LTD. RN4Z 4. Absolute maximum ratings Item Symbol Unit Rating Conditions 1 Transient Peak Reverse Voltage VRSM V 200 2 Peak Reverse Voltage VRM V 200 3 Average Forward Current IF(AV) A 3.5 4 Peak Surge Forward Current IFSM A 120 5 I2t Limiting Value I2t A2s 72 6 Junction Temperature Tj ℃ -40～+150 7 Storage Temperature Tstg ℃ -40～+150 Refer to Derating of 7 10msec. Half sinewave, one shot 1msec≦t≦10msec D es ig ns No. Symbol Unit V Forward Voltage Drop VF 2 Reverse Leakage Current IR 3 Reverse Leakage Current Under High Temperature IF=3.5A 50 max. VR=VRM mA 6.0 max. VR=VRM, Tj=150℃ trr1 ns 100 max. IF=IRP=500mA 90% Recovery point, trr2 ns 50 max. IF=500mA，IRP=1A 75% Recovery point, Rth(j-l) ℃/W 8.0 max. Between Junction and Lead uA de H･IR en m Thermal Resistance N ot R ec o 5 Reverse Recovery Time m 4 Conditions 0.92 max. d 1 Value rN Item fo No. ew 5. Electrical characteristics (Ta=25℃ ，unless otherwise specified) ‘110518 SSA-03953 2／7 61426-01 SANKEN ELECTRIC CO., LTD. RN4Z 6. Characteristics IF(AV) － PF 4.0 Tj=150℃ t T Forward Power Dissipation (W) 3.0 t/T=1/6 t/T=1/3,sinewave ns PF (W) 2.0 es ig t/T=1/2 DC 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 rN 0.0 ew D 1.0 IF(AV) (A) d fo Average Forward Current (A) t m ec o 1.0 R 1-t/T=5/6 1-t/T=2/3 0.5 N ot PR (W) Reverse Power Dissipation (W) T m Tj=150℃ en 1.5 de VR － P R 1-t/T=1/2 sinewave 0.0 0 100 200 VR (V) Reverse Voltage (V) ‘110518 SSA-03953 3／7 61426-01 SANKEN ELECTRIC CO., LTD. RN4Z 7. Derating Tl － IF(AV) VR=200(V) 3.5 3.0 t/T=1/6 DC Average Forward Current (A) 2.5 t/T=1/3 ns IF(AV) (A) 2.0 es ig 1.5 sinewave 1.0 t t/T=1/2 T 0.0 105 110 115 120 125 130 135 rN 100 ew 0.5 D Tj=150℃ 140 145 150 Tl (℃) N ot R ec o m m en de d fo Lead Temperature (℃) ‘110518 SSA-03953 4／7 61426-01 SANKEN ELECTRIC CO., LTD. RN4Z 8. Package information 8-１Package type, physical dimensions and material 50.0±1.0 8.0±0.2 ※2 8-２Appearance The body shall be clean and shall not bear any stain, rust or flaw. Dimensions in ㎜ ew 8-３Marking es ig The allowance position of Body against the center of whole lead wire is 0.5mm(max.) The centric allowance of lead wire against center of physical body is 0.3mm(max.) The burr may exit up to 2mm from the body of lead ns ※1 D ※1 ※2 ※3 φ1.4±0.1 φ6.5±0.2 ※3 rN ① Type number：RN4Z ② Lot number 1 First digit: Last digit of Year Second digit: Month From 1 to 9 for Jan. to Sep. O for Oct., N for Nov., and D for Dec. ③ Lot number 2 (ten days) ･： Top of the month ･･： Middle of month ･･･： End of month ① ③ ② ③ R ec o m ② m ① en de d fo カソード表示 Cathode Band N ot 9. Internal structure diagram ① ② Weight of products: Approx. 1.2g ‘110518 ③ No. Name of part Materials ① Plastic body Epoxy Resin ② Chip Silicon ③ Leads Solder Dipped Silver plated copper wire SSA-03953 5／7 61426-01 SANKEN ELECTRIC CO., LTD. 10. RN4Z Reliability No. Item Rating Conditions 1 Thermal Fatigue Test 5000 cycles ⊿Tj=100℃ 2 High Temperature Reverse Bias Test 1000 hours 3 Humidity Reverse Bias Test 500 hours 4 High Temperature Storage Test 1000 hours 5 Moisture Resistance Test 1000 hours 6 Thermal Shock Test 100 cycles Ice-water(5min.) ~ R.T.(20sec.) ~ Boiling-water(5min.) 7 Temperature Cycle Test 100 cycles -40℃(30min.) ~ +150℃(30min.) 8 Pressure Cooker Test 48 hours 2.03×105Pa, 100%R.H., Unsaturated equipment 10 sec. 260±5℃, Dipping up to 1.5mm form case 95% 11 Lead Bend Test 2 cycles 12 Lead Pull Test 13 Lead Twist Test 14 Drop Test es ig D 380±5℃, Using soldering iron 245±5℃, 5±0.5sec., Using rosin flux d de 10 sec. Apply EIAJ ED 4701/400 10 times Naturally drop from 1m height on maple plate m m en 2 times ec o Acceptance Criteria 85%R.H. ns Ta=85℃, rN Solder ability Test VR=VRM×0.8(D.C.) fo 10 R.H.=85%, Ta=150℃ Resistance to Soldering Heat Test 3.5 sec. 11. Ta=85℃, VR=VRM(Half sine wave) ew 9 Ta=120℃, R (1)Item No.1~9 The product shall meet the electrical specifications in paragraph 5 satisfy 1 and 2 after being exposed to normal temperature for less than 24 hours in 2 hours or more satisfy 1 and 2. N ot (2)Item No.10 The product shall meet the rating. (3)Item No.11~14 There shall be no trouble in testing and the electrical characteristics in paragraph 5 ‘110518 SSA-03953 6／7 61426-01 SANKEN ELECTRIC CO., LTD. RN4Z 12. Cautions and warnings Application and operation examples described in this document are quoted for the sole purpose of reference for the use of the products herein and Sanken can assume no responsibility for any infringement of industrial property rights, intellectual property rights or any other rights of Sanken or any third party which may result from its use.  Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semiconductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems against any possible injury, death, fires or damages to the society due to device failure or malfunction.  Sanken products listed in this document are designed and intended for the use as components in general purpose electronic equipment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). Please return to us this document with your signature(s) or seal(s) prior to the use of the products herein. When considering the use of Sanken products in the applications where higher reliability is required (transportation equipment and its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), please contact your nearest Sanken sales representative to discuss, and then return to us this document with your signature(s) or seal(s) prior to the use of the products herein. The use of Sanken products without the written consent of Sanken in the applications where extremely high reliability is required (aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited.  In the case that you use our semiconductor devices or design your products by using our semiconductor devices, the reliability largely depends on the degree of derating to be made to the rated values. Derating may be interpreted as a case that an operation range is set by derating the load from each rated value or surge voltage or noise is considered for derating in order to assure or improve the reliability. In general, derating factors include electric stresses such as electric voltage, electric current, electric power etc., environmental stresses such as ambient temperature, humidity etc. and thermal stress caused due to self-heating of semiconductor devices. For these stresses, instantaneous values, maximum values and minimum values must be taken into consideration. In addition, it should be noted that since power devices or IC’s including power devices have large self-heating value, the degree of derating of junction temperature (Tj) affects the reliability significantly.  When using the products specified herein by either (i) combining other products or materials therewith or (ii) physically, chemically or otherwise processing or treating the products, please duly consider all possible risks that may result from all such uses in advance and proceed therewith at your own responsibility.  Anti radioactive ray design is not considered for the products listed herein.  Sanken assumes no responsibility for any troubles, such as dropping products caused during transportation out of Sanken’s distribution network. N ot R ec o m m en de d fo rN ew D es ig ns  ‘110518 SSA-03953 7／7 61426-01